News

moodlite - Coming soon


Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - DevilsDJ

Pages: 1 2
1
Let's talk 3D printers... / Re: My new toy - JGAURORA A5
« on: February 19, 2019, 08:02:54 PM »
Did you have problems with prints sticking to bed , so far 2 prints made - 2 prints had parts get lifted from bed , bed at 75C leveled as best as I can .

2
Let's talk 3D printers... / My new toy - JGAURORA A5
« on: February 16, 2019, 09:45:55 PM »
Got my new toy yesterday , Ill be testing it out for a while to see if it wil permanently replace my Anet A8 or if it will get sold :D

3
moodlite Design / Re: New simple design
« on: February 10, 2019, 10:09:39 PM »
Ooo ok good luck , keep me posted , would love to see your idea

4
moodlite Design / Re: New simple design
« on: February 10, 2019, 09:57:51 PM »
Check the one I just made. Um it should print fine the one you made , but how would you connect it to the top ?

5
moodlite Design / Re: New simple design
« on: February 10, 2019, 09:53:28 PM »
I made this , dont know if this is exactly what you need , please let me know if you need anything else or any information , glad to help

6
moodlite Design / Re: New simple design
« on: February 10, 2019, 09:28:27 PM »
First make the base figure , then offset that with the total size of the walls ( the bottom part of the wall and the one that interacts with the top part ) , extrude that , then offset that with the size of the top part of the wall that interacts with the top part and extrude that

7
moodlite Design / Re: New simple design
« on: February 10, 2019, 08:54:21 PM »
initially without the corners

8
moodlite Design / Re: New simple design
« on: February 10, 2019, 11:34:18 AM »
I am still fairly new to fusion 360 myself so prob the way I do things isnt the easiest or fastest but still it does the job. I drew the triangle , drew lines on each side from the corner (measure what you need i did those 25mm on the one i showed you , then extruded that 1mm . After that do an offset on that ( i did 3.2mm inwards) raise that by 13,4mm(cuz you can do a 0,6mm top) , then do an offset on that edge (1,2mm) and raise that 5mm so you get a total of 19,4mm and when you connect the top part which  would be 0.6mm thick it will become 20mm in total.

The holes I did by just finding the center of what part you want to put a hole in and drawing a circle of the size you want the hole to be , then extruding it towards the side using the cut function.


9
moodlite Design / Re: New simple design
« on: February 10, 2019, 09:33:33 AM »
Did that in like 5min or less . If you can explain exactly what you want , with the dimensions  I can make it for you

10
moodlite Design / Re: How to do triangle patterns with three edges?
« on: February 10, 2019, 09:12:12 AM »
I would say just get the bottom step file and widen the existing cable guides to fit more cables. something like this:

Now that I think about it you might spend some time (more then 4min i sped to widen the guides) and make the guides as tall as the cables and lower the inside pyramid to get better diffusion too.

11
moodlite Design / Re: Better diffusion
« on: February 10, 2019, 07:14:02 AM »
https://www.reddit.com/r/prusa3d/comments/aj9p3a/i_designed_my_own_scattered_rectilinear_infill/

Look at that amazing diffusing happening with this guy's developed infill option...  Has anyone tried this yet?

That guys leds are on the bottom not the sides and the distance between bottom and diffuser is bigger than with the moodlite. For me I made a 5mm taller top with pla diffuser (just remodeled the original top to be 5mm taller , moved the pins and made the sides a bit thicker for less diffusion on the sides) I am thinking of remodeling the tile top frame only so I can fit a 2mm acrylic which I will be sandpaper frosting with the top tile raised 5mm again . Will post results when I do.

Note: this is my raised tile top , I'd say it is much better for diffusion then the original , you cant see the pyramid almost at all. The photos dont do it justice , looks better in real life

12
moodlite Design / Re: New simple design
« on: February 09, 2019, 08:16:12 PM »
Something like this , or with edges ?

13
moodlite Design / Re: How to do triangle patterns with three edges?
« on: February 09, 2019, 07:45:43 PM »
The simplest way to go with this kind of pattern not using connectors and just using cables to connect the way you want to , just loop the cable either on the inside or use the bottom space .something like the pic , or whatever you decide upon

14
moodlite Design / Re: New moodlite Designs Release - Help required
« on: February 09, 2019, 07:30:50 PM »
Oooo Ioalby did what I was thinking at one point , just using the male connector and pins ,thats why the servo extenders dont work on his cuz the female connector is thicker and wider then the male one.
NOTE: Im calling them female and male connectors but actually the male on the servo extenders is the female connector and the male ones are the ones in the photo ,  the exterders are actually male to male with pins inside that bigger connector(female for the extender) that connect one male to another.

I was actually thinking of using a ribbon cable (thin and all) and some kind of thinner connector as to be able to lower the inner pyramid but so far havent figured it out.

15
moodlite Design / Re: New moodlite Designs Release - Help required
« on: February 09, 2019, 05:46:44 PM »
I havent checked Ioalby's design closely , the Y ones fit the original 2nd version one  , I dont think there is any diffrence in size between the Y ones and the normal ones since its just one more female connector added.

Pages: 1 2

SMF spam blocked by CleanTalk